Honda HSM1380i Owner'S Manual Download Page 19 | Manualshive

Page: 19 / 130

background image

17

Drive control warning indicator (orange)

The drive control warning indicator (orange) turns on when the engine
switch is turned from OFF to ON. The indicator (orange) turns off when
the engine is started. The indicator goes off while the engine is
running. If the indicator does not come on when starting and it comes
on or blinks while the engine is running, contact your authorized Honda
snow thrower dealer.
If the orange indicator blinks, the drive control protection system may
be activated because of such things as a drive control system problem
or overload. See page 71 for the protection system.

Charging indicator

The charging indicator (red) turns on when the engine switch is turned
from OFF to ON. The indicator turns off when the engine is started. If
the indicator does not come on when starting or comes on while the
engine is running, contact your authorized Honda snow thrower
dealer.

DRIVE CONTROL WARNING
INDICATOR (orange)

CHARGING INDICATOR (red)

36V156410.book 17 ページ２０１８年１０月１０日　水曜日　午前１１時３０分

«
...
17
18
19
20
21
...
»

Summary of Contents for HSM1380i



































































































































Reviews:

No comments

Related manuals for HSM1380i

Brand: Stihl Pages: 20

Brand: SNOWJOE Pages: 48

Brand: Yard force Pages: 6

Brand: ICP Pages: 12

Brand: SNOWJOE Pages: 20

Brand: Shindaiwa Pages: 40

Brand: Stihl Pages: 20

Brand: GreenWorks Pro Pages: 9

Brand: Black & Decker Pages: 6

Brand: Black & Decker Pages: 4

Brand: Black & Decker Pages: 4

Brand: Black & Decker Pages: 4

Brand: Black & Decker Pages: 10

Brand: Black & Decker Pages: 16

Brand: Husqvarna Pages: 32

Brand: Husqvarna Pages: 12

Brand: Husqvarna Pages: 40

Brand: Husqvarna Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands