Honda EU 1000i Owner'S Manual Download

Page: 51 / 92

SERVICING YOUR GENERATOR

AIR CLEANER SERVICE

FOAM AIR
FILTER

COVER SCREW

RUBBER SEAL

MAINTENANCE COVER

RUBBER AIR
GUIDE

AIR CLEANER
COVER

AIR CLEANER CASE

Operating the engine without an air filter or with a damaged air filter
will allow dirt to enter the engine, causing rapid engine wear. This type
of damage is not covered by the

Distributor’s Limited Warranty.

Loosen the cover screw and remove
the maintenance cover.

Press the latch tab on the top of the
air cleaner case, and remove the air
cleaner cover.

Reinstall the air filter.

Make sure that the rubber seal is set
in the groove of the air cleaner
cover.

Reinstall the air cleaner cover by
inserting the lower tab and the latch
tab.

Reinstall the maintenance cover,
and tighten the cover screw
securely.

Check the foam air filter to be sure it
is clean and in good condition. If the
foam air filter is dirty, clean it as
described on page

. Replace the

foam air filter if it is damaged.

10/03/11 13:01:14 31ZT3620_050

Summary of Contents for EU 1000i





























































































Search results

Summary of Contents for EU 1000i

Reviews:

Related manuals for EU 1000i

Brands by name

Popular brands

Honda EU 1000i, Owner'S Manual

Search results

Summary of Contents for EU 1000i

Reviews:

Related manuals for EU 1000i

Brands by name

Popular brands