Honda EU 1000i Owner'S Manual Download

Page: 54 / 92

−

SERVICING YOUR GENERATOR

SEALING WASHER

0.024

0.028 in

(0.6

0.7 mm)

SIDE ELECTRODE

Inspect the spark plug. Replace
it if the electrodes are worn or if
the insulator is cracked,
chipped, or fouled.

Measure the spark plug
electrode gap with a wire-type
feeler gauge. Correct the gap, if
necessary, by carefully bending
the side electrode.

The gap should be:

Make sure that the spark plug sealing washer is in good condition,
and thread the spark plug in by hand to prevent cross-threading.

If reinstalling a used spark plug, tighten 1/8

1/4 turn after the spark

plug seats.
If installing a new spark plug, tighten 1/2 turn after the spark plug
seats.

0.024

0.028 in (0.6

0.7 mm)

After the spark plug is seated, tighten with a spark plug wrench to
compress the sealing washer.

A loose spark plug can overheat and damage the engine.
Overtightening the spark plug can damage the threads in the
cylinder head.

Reinstall the spark plug cap on the spark plug securely.

Reinstall the spark plug maintenance cover.

10.

10/03/11 13:01:42 31ZT3620_053

Summary of Contents for EU 1000i





























































































Search results

Summary of Contents for EU 1000i

Reviews:

Related manuals for EU 1000i

Brands by name

Popular brands

Honda EU 1000i, Owner'S Manual

Search results

Summary of Contents for EU 1000i

Reviews:

Related manuals for EU 1000i

Brands by name

Popular brands