Honda CRF125F 2021 Owner'S Manual Download Page 87 | Manualshive

Page: 87 / 132

background image

77

4. Check the chain slider (2) for wear.

If the depth (3) of the chain slider
reaches the service limit, have your
dealer replace the chain slider.

Service Limit:

3 mm (0.1 in)

5. Measure a section of the drive chain to

determine whether the chain is worn
beyond its service limit. Remove the
drive chain and measure the distance
between a span of pins from pin centre to
pin centre. If the distance exceeds the
service limit, the chain is worn out and
should be replaced.

New Chain:

508 mm (20.0 in)

Service Limit:

518 mm (20.4 in)

Measure a span of :

41

pins.

(2) Chain slider
(3) Depth

(2)

(3)

(3)

(3)

37K28B31.book Page 77 Monday, July 26, 2021 6:11 PM

«
...
85
86
87
88
89
...
»

Summary of Contents for CRF125F 2021





































































































































Reviews:

No comments

Related manuals for CRF125F 2021

Brand: Honda Pages: 178

Brand: Cobra Pages: 38

Brand: Memphis Shades Pages: 2

Brand: Biltema Pages: 2

Brand: TREND Pages: 38

Brand: X-lite Pages: 96

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 114

YZF-R1P 2001-2003

Brand: Yamaha Pages: 439

Brand: DYNATEK Pages: 5

Brand: APRILIA Pages: 216

Brand: Menuett Pages: 27

Brand: Benelli Pages: 582

CRF50F 2004-2015

Brand: Honda Pages: 180

Brand: Honda Pages: 211

Brand: 6KU Pages: 17

Brand: 130R Pages: 57

Brand: ConforTeck Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands