manualshive.com logo in svg

Honda CRF125F 2021, Owner'S Manual

Share
Download
Honda CRF125F 2021 Owner'S Manual Download Page 112

102

3. To prevent rusting in the cylinder, 

perform the following: 
• Remove the spark plug cap from the 

spark plug. Using tape or string, 
secure the cap to any convenient 
plastic body part so that it is 
positioned away from the spark plug.

• Remove the spark plug from the 

engine and store it in a safe place. Do 
not connect the spark plug to the 
spark plug cap.

• Pour a tablespoon (15 – 20 cm

3

) of 

clean engine oil into the cylinder and 
cover the spark plug hole with a piece 
of cloth.

• Crank the engine several times to 

distribute the oil.

• Reinstall the spark plug and spark 

plug cap.

4. Remove the battery. Store in an area 

protected from freezing temperatures 
and direct sunlight.
Slow charge the battery once a month.

5. Wash and dry the motorcycle. Wax all 

painted surfaces. Coat chrome with 
rustinhibiting oil.

6. Lubricate the drive chain (page 79). 
7. Inflate the tyres to their recommended 

pressures. Place the motorcycle on 
blocks to raise both tyres off the ground.

8. Cover the motorcycle (don’t use plastic 

or other coated materials) and store in 
an unheated area, free of dampness with 
a minimum of daily temperature 
variation.
Do not store the motorcycle in direct 
sunlight.

37K28B31.book  Page 102  Monday, July 26, 2021  6:11 PM

Summary of Contents for CRF125F 2021





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands