Honda CRF125F 2021 Owner'S Manual Download Page 84

Page: 84 / 132

Freeplay Adjustment:
1. Adjust freeplay with the throttle cable

adjuster (1). Measured in grip rotation,
the standard throttle grip freeplay is:

2 – 6 mm (0.1 – 0.2 in)

2. To adjust the freeplay, slide the throttle

cable boot (2), then loosen the lock nut
(3) and turn the cable adjuster.

3. After adjustment, check again for

smooth rotation of the throttle grip from
the fully closed to the fully open position
with the steering to the full right and left
as well as straight ahead.

If proper throttle freeplay cannot achieved,
contact your dealer.

(1) Cable adjuster
(2) Cable boot
(3) Lock nut

(A) Decrease freeplay
(B) Increase freeplay

(3)

(2)

(A)

(B)

(1)

37K28B31.book Page 74 Monday, July 26, 2021 6:11 PM

Summary of Contents for CRF125F 2021





































































































































Search results

Summary of Contents for CRF125F 2021

Reviews:

Related manuals for CRF125F 2021

Brands by name

Popular brands

Honda CRF125F 2021, Owner'S Manual

Search results

Summary of Contents for CRF125F 2021

Reviews:

Related manuals for CRF125F 2021

Brands by name

Popular brands