manualshive.com logo in svg

Honda CRF125F 2021, Owner'S Manual

Share
Download
Honda CRF125F 2021 Owner'S Manual Download Page 65

55

SAFETY PRECAUTIONS

• Make sure the engine is off before you 

begin any maintenance or repairs. This 
will help eliminate several potential 
hazards:

✽

Carbon monoxide poisoning from 

engine exhaust.

Be sure there is adequate ventilation 
whenever you operate the engine.

✽

Burns from hot parts.

Allow the engine, muffler, brakes and 
other high-temperature parts to cool 
before servicing as you can get burned.

✽

Injury from moving parts.

Do not run the engine unless 
instructed to do so.

• Read the instructions before you begin, 

and make sure you have the tools and 
skills required.

• To help prevent the motorcycle from 

falling over, park it on a firm, level 
surface, using the side stand or a 
maintenance stand to provide support.

• To reduce the possibility of a fire or 

explosion, be careful when working 
around petrol. Use only nonflammable 
solvent, not petrol, to clean parts. Keep 
cigarettes, sparks and flames away from 
all fuel-related parts.

Remember that your dealer knows your 
motorcycle best and is fully equipped to 
maintain and repair it.

To ensure the best quality and reliability, 
use only new Honda Genuine Parts or their 
equivalents for repair and replacement.

Changing parts can affect your health and 
safety. We recommend that you consult 
your dealer if you do not have the proper 
skill and tools to change parts on your own.

37K28B31.book  Page 55  Monday, July 26, 2021  6:11 PM

Summary of Contents for CRF125F 2021





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands