Honda CRF125F 2021 Owner'S Manual Download Page 56 | Manualshive

Page: 56 / 132

background image

46

Starting Procedure

This motorcycle has a fuel-injected engine.
Follow the procedure indicated below.

Any Air Temperature

1. Using the start button

With the throttle completely closed,
press the start button.
Using the kickstarter
Lightly depress the kickstarter until
resistance is felt.
Then let the kickstarter return to the top
of its stroke.
With the throttle completely closed,
operate the kickstarter starting from the
top of the stroke, kick through to the
bottom with a rapid, continuous motion.

Allowing the kickstarter to snap back freely
against the pedal stop can damage the
engine case.

2. If you cannot start the engine, open the

throttle slightly (about 3 mm (0.1 in),
without freeplay).

about 3 mm (0.1 in),
without freeplay

37K28B31.book Page 46 Monday, July 26, 2021 6:11 PM

«
...
54
55
56
57
58
...
»

Summary of Contents for CRF125F 2021





































































































































Reviews:

No comments

Related manuals for CRF125F 2021

TroyLee Designs

Brand: A3 HELMET Pages: 244

Brand: Big Dog Pages: 100

Brand: KTM Pages: 25

Brand: PUIG Pages: 2

Brand: TVS Pages: 48

Brand: DYNATEK Pages: 3

Brand: DYNATEK Pages: 2

Brand: Yamaha Pages: 24

Brand: Yamaha Pages: 34

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 92

WARRIOR XV17PCT

Brand: Yamaha Pages: 97

WARRIOR XV17PCC

Brand: Yamaha Pages: 97

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 95

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands