Honda 1992 Accord Wagon Owner'S Manual Download Page 58

Page: 58 / 166

Hood and Parking Brake

Hood

To release the hood latch, pull hack on

the handle located under the dash on
the driver's side.

The hood latch is spring-loaded, so the hood will pop up slightly.

Release the safety catch under the front center of the hood by pushing

the rubber-tipped handle up. Lift the hood and prop it open with the
support rod. To close, take the support rod down, place it back in its

holder, lower the hood until it is approximately one foot (30 cm) from
the closed position, then let it drop. Be sure the hood is securely

latched before driving away.

Parking Brake

To apply the parking brake, pull
up on the lever. To release it, pull
up slightly, push the button, and
lower the lever; when fully
released, the BRAKE (US cars), or

(Canadian cars) warning

light will go out.

Pull to

release.

SUPPORT ROD

Summary of Contents for 1992 Accord Wagon







































































































































































Search results

Summary of Contents for 1992 Accord Wagon

Reviews:

Related manuals for 1992 Accord Wagon

Brands by name

Popular brands

Honda 1992 Accord Wagon, Owner'S Manual

Search results

Summary of Contents for 1992 Accord Wagon

Reviews:

Related manuals for 1992 Accord Wagon

Brands by name

Popular brands