background image

-7- 

ALFA IN a.s. ©                                 

 

 

                  

www.alfain.eu

 

in rain or snow.

 

4. 

Ensure proper grounding clamping pliers, which also reduces the risk of 
electric shock.

 

5. 

Use prescribed protective utilities, keep them dry.

 

6. 

Arc welding produces intense electric and magnetic emissions that may 
interfere with the proper function of cardiac pacemakers, hearing aids, or 
other  electronic  health  equipment.  Persons  who  work  near  plasma  arc 
cutting applications should consult their medical health professional and 
the manufacturer of the health equipment to determine whether a hazard 
exists.

 

7. 

Never aim the torch against the eyes, body or other person.

  

3. CONDITIONS OF USE 

1.  This equipment must only be used by qualified personnel.  
2.  During  installation,  any  electric  work  must  only  be  carried  out  by  trained 

personnel. 

3.  Device complies with

 

IEC 61000-3-12

.

 

4.  Do not expose the plasma machine to direct sunlight or to rain or snow. This 

equipment conforms to protection rating IP21S. 

5.  Working ambient temperature between -10 and +40 °C. 
6.  Relative humidity below 90% at +20 °C. 
7.  Up to 3000 m altitude. 
8.  Place the machine the way that the cooling air can enter the vents without 

restriction to. It is necessary to ensure that no impurities, especially metal 
particles are not drawn into the machine. 

9.  Welding machine in terms of interference suppression is intended primarily 

for industrial premises. In the case of use of other areas may be need for 
special measures (see EN 60974-10). 

10. 

The machine must be protected against

 

a.  Moisture and rain and snow 
b.  Mechanical damage 
c.  Draft and any ventilation of neighbouring machine 
d.  Excessive overloading - crossing technical parameters 
e.  Rough handling 

ELECTROMAGNETIC COMPATIBILITY 

The welding device is in terms of interference designed primarily for industrial 
areas. It meets the requirements of EN 60974-10 class A and it isn’t designed 
for using in residential areas, where the electrical energy is supplied by public 
low-voltage  power  supply  network.  It  can  be  here  potential  problems  with 
ensuring  of  electromagnetic  compatibility  in  this  areas,  due  to  interference 
caused by power lines as well as the radiated interference. During operation, 
the device may be the source of interference. 

Summary of Contents for MG-160



















Reviews: