HOMER tools MG-160 Operating Manual Download Page 14

Page: 14 / 18

-14-

ALFA IN a.s. ©

www.alfain.eu

Fig. 5 – Gas fitting

Pos.

Description

Gas cylinder

Cylinder valve

Gas heater connector

Pressure reducer

High pressure manometer

Low pressure manometer

Adjusting screw

Gas outlet

Solenoid valve

F10

Chain

The gas cylinder cannot be fixed to the HOMER MG-160. It can be fixed onto
the welders cart or other fixing appliance according to the user´s manual of
such appliance and in accordance with the safety rules.

1. Connect the pressure reduction valve on the gas cylinder.
2. Connect the gas hose to gas outlet

on the valve and the gas inlet on the

machine.

3. Open the

cylinder valve.

4. Set the voltage switch

to the position

5. Adjust the amount of gas on the reduction gas valve (it is not a part of the

welding machine) by the

adjusting screw.

Summary of Contents for MG-160



















Search results

Summary of Contents for MG-160

Reviews:

Related manuals for MG-160

Brands by name

Popular brands

HOMER tools MG-160, Operating Manual

Search results

Summary of Contents for MG-160

Reviews:

Related manuals for MG-160

Brands by name

Popular brands