Hollis Prism 2 User'S & Service Manual Download Page 63

Page: 63 / 67

Doc. 12-4091 - r01 (9/12/12)

PG-63

SERVICE

GUIDE

SUPPORT: TOLL-FREE 888-383-DIVE │ FAX 510-729-5115 │ E-MAIL [email protected]

2002 DESIGN

(

2012)

8. Remove the

ELECTRICAL CONNECTORS (5)

from the

OXYGEN SENSORS (7)

NOTE:

A small flat blade screwdriver, preferably a jeweler's screwdriver, may be used to release the

electrical connector locking mechanism without damaging the connectors.

9. Inspect the

SENSOR (7)

contacts for damage or corrosion. Clean or discard the sensor as needed.

CAUTION: The electrical connectors have thin precious metal plating. DO NOT scrape corrosion from

contacts with a hard sharp object. DO NOT use abrasives, petroleum distillates, silicone based clean-

ers, erasers, combustible chemicals, or any other harsh cleaners. Hollis recommends the use of DeoxIT

Gold® GN5 for cleaning the OXYGEN SENSOR (7) electrical contacts and the contacts on the WIRE

HARNESS (5).

10. Being careful not to physically damage the electrical connectors, remove and inspect the

WIRE HARNESS

(5)

for corrosion and damage. Clean or discard as appropriate.

11. Inspect the

BULKHEAD CONNECTOR(4)

, that the

WIRE HARNESS (5)

plugs into, on the

SCRUBBER

HEAD (1)

for corrosion or damage. Clean as appropriate.

MILLIVOLT/LINEARITY TEST & CLEANING

WARNING: Any SENSORS (7) being used in the PRISM 2 unit must pass this Millivolt/Linearity Test.

TECHNICIANS ONLY:

NOTE:

Any opened SENSORS (7) must have serial numbers, date of testing, and mV reading data re-

sults documented for the customer on a copy of the Hollis Rebreather Receiving and Final Inspection

Form. You should retain the original copy for your records.

WARNING: The SENSORS (7) must be installed in the PRISM 2, tested, and pass the Final Inspection

Procedure before returning the PRISM 2 unit to your customer for use. The Final Inspection Proce-

dure may be found in the Receiving and Final Inspection Section of the PRISM 2 Service Guide.

1. Visually inspect the

OXYGEN SENSOR'S (7)

electrical terminal, Teflon membrane, and plastic body for dirt,

corrosion, or physical damage.

2. The terminals may be cleaned using Deoxit Gold

™

GN5. Use the chemical sparingly and wipe any excess

away with a clean lint free cloth. If the terminals are physically damaged the sensor

MUST NOT BE USED

3. The plastic body of the

SENSOR (7)

should be wiped clean with a lint free cloth. If needed, sparingly apply

Blue Gold

to the lint free cloth to clean the plastic

SENSOR (7)

body

ONLY

DO NOT

expose the

SENSOR (7)

membrane or electrical terminals to the cleaner.

4. The Teflon membrane may be gently rinsed with distilled water

ONLY

if salt crystals are present. It must then

be allowed to air dry.

WARNING: DO NOT use compressed air to dry the delicate membrane surface, or the SENSOR (7)

may be damaged.

Summary of Contents for Prism 2




































































Search results

Summary of Contents for Prism 2

Reviews:

Hollis Prism 2, User'S & Service Manual, Page: 63 / 67

Search results

Summary of Contents for Prism 2

Reviews: