Hollis Prism 2 User'S & Service Manual Download Page 47

Page: 47 / 67

Doc. 12-4091 - r01 (9/12/12)

PG-47

SERVICE

GUIDE

SUPPORT: TOLL-FREE 888-383-DIVE │ FAX 510-729-5115 │ E-MAIL [email protected]

2002 DESIGN

(

2012)

NOTE: If the Spring Assembly has seized, broken,

or fails to hold the SCRUBBER BASKET (15) se-

curely against the RED CO

₂

SEAL (28), the Spring

Assembly must be replaced. Otherwise, skip step 6.

6. If removing the Spring Assembly, remove the

LOCK-

NUT (3)

counterclockwise with a 3/8" driver

(Fig. 6)

Discard the

LOCKNUT (3)

. Inspect the

SPRING (5)

and

SPRING PAD (4)

for signs of decay, damage, or corro-

sion. Discard if found.

NOTE: The LATCH KEEPER (23) only needs to

be removed if damaged. If it is in good condition

skip step 7.

7. Turning counterclockwise, remove the

SCREWS (24)

using a 5/64" Allen driver

(Fig. 7)

. The

LATCH KEEPER

(23)

should slide free easily.

NOTE: The RETAINER BAND ASSEMBLY (7) only

needs to be removed if damaged or badly corroded.

If it is in good condition skip step 8.

8. Turning counterclockwise with a 3/8" open end

wrench, remove the

LOCKNUTS (14)

and

SCREWS

(13)

from the

BAND ASSEMBLY (7)

(Fig. 8)

. Discard

the

LOCKNUTS (14)

. Then slide the

BAND ASSEM-

BLY (7)

off of the

SCRUBBER BUCKET (1)

Fig. 6

Fig. 7

Fig. 8

Summary of Contents for Prism 2




































































Search results

Summary of Contents for Prism 2

Reviews:

Hollis Prism 2, User'S & Service Manual, Page: 47 / 67

Search results

Summary of Contents for Prism 2

Reviews: