Hollis Prism 2 User'S & Service Manual Download Page 21

Page: 21 / 67

Doc. 12-4091 - r01 (9/12/12)

PG-21

SERVICE

GUIDE

SUPPORT: TOLL-FREE 888-383-DIVE │ FAX 510-729-5115 │ E-MAIL [email protected]

2002 DESIGN

(

2012)

3. Disconnect the

BREATHING HOSES (13, 21)

at the

front of each

COUNTERLUNG (30, 44)

by turning the

PLASTIC FITTING NUT (19, 28)

counterclockwise

(Fig.

. Then pull the

PLASTIC ELBOW FITTING (19, 28)

straight out of the

COUNTERLUNG (30, 44) (FIG. 8)

Inspect the mating surfaces of the fittings for damage. If

damaged, replace the appropriate parts.

4. Disconnect the

BREATHING HOSES (31, 45)

from

the Scrubber Head by turning the

PLASTIC NUT FIT-

TING (34, 49)

all the way counter clockwise. Then sim-

ply lift the

HOSE (31, 45)

away from the Scrubber Head

(FIG. 9)

. Inspect the mating surfaces of the fittings for

damage. If damaged, repair and replace the appropriate

parts.

4. Unfasten the Velcro BCD Airway Retainer and Har-

ness straps holding the Counterlungs.

5. Disconnect the Quick Releases and Velcro Attach-

ment that connect the top of the

COUNTERLUNGS (30,

44)

to the Counterlung Mounting Yoke, as Shown. In-

spect the Quick Releases and Velcro Fasteners for wear

and damage, repair and replace as needed.

NOTE: The Quick Releases and Velcro Fasten-

ers are sewn in place. In the field the COUNTER-

LUNGS (30, 44) and Counterlung Mounting Yoke

can only be replaced. If shipment to the factory

is possible, contact Hollis Customer Service for

possible repairs of the existing COUNTERLUNG

(30, 44) or Counterlung Mounting Yoke.

6. Turning the

ADV MOUNTING NUT (52)

counterclock-

wise, remove the

ADV/MANUAL DILUENT ADDITION

VALVE (52) (FIG. 10)

. Inspect mating surfaces and the

RUBBER GASKET (53)

for damage. The ADV/Manual

Diluent Addition Valve is not serviceable. If damaged or

faulty, replace with new. Otherwise, follow the PRISM

2 Service and Parts Replacement Schedule (Doc. 12-

4092).

7. Turning the

OXYGEN VALVE MOUNTING NUT

(38)

counterclockwise, remove the

MANUAL OXY-

GEN ADDITION VALVE (38) (Fig. 11)

. Inspect mating

surfaces and the

RUBBER GASKET (39)

for damage.

The Manual Oxygen Addition Valve is not serviceable. If

damaged or faulty, replace with new. Otherwise, follow

the PRISM 2 Service and Parts Replacement Schedule

(Doc. 12-4092).

Fig. 9

Fig. 10

Fig. 11

Fig. 7

Fig. 8

Summary of Contents for Prism 2




































































Search results

Summary of Contents for Prism 2

Reviews:

Hollis Prism 2, User'S & Service Manual, Page: 21 / 67

Search results

Summary of Contents for Prism 2

Reviews: