background image

5

XL-FW20130RM-en-US Rev C · 2022-01-03 · Amendments and Errors Reserved · © SAF-HOLLAND, Inc., SAF-HOLLAND, HOLLAND, SAF, 
and logos are trademarks of SAF-HOLLAND S.A., SAF-HOLLAND GmbH, and SAF-HOLLAND, Inc.

Model Identification

MADE IN XXXXX

SCAN QR CODE FOR PRODUCT INFORMATION

Model No. XXXXXXXXXXXXXXX

Serial  No. XXXXXXXXXXXXXXX

U.S. AND FOREIGN PATENTS APPLY   Ph: (888) 396-6501 or 52.1.55.5456.8641

CONSULT PRODUCT INFORMATION AT 
LITKITS.SAFHOLLAND.COM PRIOR TO USING 
THIS PRODUCT. FAILURE TO PROPERLY INSTALL, 

MAINTAIN & OPERATE THIS PRODUCT COULD RESULT IN TRACTOR 
TRAILER SEPARATION CAUSING SERIOUS INJURY OR DEATH.

QR

CODE

Figure 1

Figure 4

Figure 3

Figure 2

2.  Model Identification

This manual contains the installation procedures for SAF-
HOLLAND rebuild kits RK-351-TT and RK-351-UBT. Prior to 
rebuilding, verify the correct rebuild kit by identifying the fifth 
wheel model number, which can be found on the fifth wheel 
serial tag.

The fifth wheel serial tag is located on the side of the fifth 
wheel top plate, above the bracket pin location or near the 
pickup ramps 

(Figure 1)

. The fifth wheel model number and 

serial number are listed on the tag as illustrated 

(Figure 2)

.

For 

FW35TT/XA-351-TT

 Series fifth wheels 

(Figure 3)

, use 

the RK-351-TT Rebuild Kit.

For 

FW67/XA-351-UBT

 Series fifth wheels 

(Figure 4)

, use 

the RK-351-UBT Rebuild Kit.

FW35TT/XA-351-TT

FW67/XA-351-UBT

BRACKET PIN NUTS 

WELDED ONTO CASTING

Summary of Contents for FW35TT/XA-351-TT Series





















Reviews: