background image

3

XL-FW20130RM-en-US Rev C · 2022-01-03 · Amendments and Errors Reserved · © SAF-HOLLAND, Inc., SAF-HOLLAND, HOLLAND, SAF, 
and logos are trademarks of SAF-HOLLAND S.A., SAF-HOLLAND GmbH, and SAF-HOLLAND, Inc.

Contents .........................................................................Page

Contents .........................................................................Page

Introduction ......................................................................... 3
Notes, Cautions and Warnings .............................................. 3
Section 1 – General Safety Instructions ................................ 4
Section 2 – Model Identification........................................... 5
Exploded View ..................................................................... 6
Parts List.............................................................................. 7
Section 3 – Top Plate Removal ............................................. 8
Section 4 – Yoke Installation ................................................. 9
Section 5 – Lock Installation ............................................... 10  

Section 6 – Cam Plate Installation....................................... 11
Section 7 – Secondary Lock Installation ............................... 13
Section 8 – Cam Spring Installation .................................... 14
Section 9 – Air Cylinder Installation ................................... 15
Section 10 –  Upshock Cushions, Pocket Inserts  

and Brackets Inspection ................................. 16

Section 11 – Top Plate Installation ...................................... 18
Section 12 – Operation Check ............................................. 19

Introduction

This manual provides the information necessary to properly 
rebuild FW35TT/XA-351-TT Series top plates, and FW67/ 
XA-351-UBT elevating fifth wheel top plates.

Read this manual before using or servicing this product. 
Updates to this manual, which are published as necessary,  
are available on the internet at www.safholland.us.

When replacement parts are necessary, SAF-HOLLAND

®

 

requires the use of only SAF-HOLLAND Original Parts. A list 
of technical support locations that supply SAF-HOLLAND 
Original Parts and an Aftermarket Parts Catalog are available 
on the internet at www.safholland.us or contact Customer 
Service at 888-396-6501.

Notes, Cautions, and Warnings

Before starting work on any SAF-HOLLAND fifth wheel 
assembly, read and understand all the safety procedures 
presented in this manual. This manual contains the terms 
"NOTE", "IMPORTANT", "CAUTION", and "WARNING" 
followed by important product information. These terms are 
defined as follows:

NOTE:

   Includes additional information to enable  

accurate and easy performance of procedures.

IMPORTANT:

   Includes additional information that,  

if not followed, could lead to hindered 
product performance.

Used without the safety alert symbol, 
indicates a potentially hazardous 
situation which, if not avoided, could 
result in property damage.

Indicates a potentially hazardous 
situation which, if not avoided, could 
result in minor or moderate injury.

Indicates a potentially hazardous 
situation which, if not avoided, could 
result in death or serious injury.

Summary of Contents for FW35TT/XA-351-TT Series





















Reviews: