background image

WARRANTY

Hobbico

®

, Inc. guarantees this kit to be free from defects in both material and workmanship at the date of

purchase. This warranty does not cover any component parts damaged by use or modification. In no case shall
Hobbico’s liability exceed the original cost of the purchased model. Further, Hobbico reserves the right to change
or modify this warranty without notice. In that Hobbico has no control over the final assembly, no liability shall
be assumed nor accepted for any damage resulting from the use by the user of the final user-assembled product.
By the act of using the user-assembled product, the user accepts all resulting liability. If the buyers are not
prepared to accept the liability associated with the use of this product, they are advised to return this kit
immediately in new and unused condition to the place of purchase.
To make a warranty claim send the defective part or item to Hobby Services at the address below:

Include a letter stating your name, return shipping address, as much contact
information as possible (daytime telephone number, fax number, e-mail address),
a detailed description of the problem and a photocopy of the purchase receipt.
Upon receipt of the package the problem will be evaluated as quickly as possible.

Wingspan:

68 in [1725mm] 

Wing Area:

462 sq in [29.8 dm

2

Weight:

42–46 oz [1190–1305 g]

Wing Loading:

13.1–14.3 oz/sq ft [40–44 g/dm

2

Length:

45 in [1130mm] 

Radio: 

3-channel with 2 standard servos

Entire Contents © Copyright 2006

HCAZ2210 for HCAA2210 V1.0

Hobby Services

3002 N. Apollo Dr.  Suite 1

Champaign IL  61822

USA

READ THROUGH THIS MANUAL BEFORE STARTING
CONSTRUCTION. IT CONTAINS IMPORTANT
INSTRUCTIONS AND WARNINGS CONCERNING
THE ASSEMBLY AND USE OF THIS MODEL.

Champaign, Illinois

(217) 398-8970 ext. 5

[email protected]

Summary of Contents for UPSTAR





















Reviews: