background image

READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.

Entire Contents  © 2012 Hobbico, Inc.

TOPA1025 Mnl

WARRANTY

Top Flite

®

 Model Manufacturing Co.

 guarantees this kit to be free from defects in both material and 

workmanship at the date of purchase. This warranty does not cover any component parts damaged by use 
or modification. 

In no case shall Top Flite’s liability exceed the original cost of the purchased kit.

 

Further, Top Flite reserves the right to change or modify this warranty without notice.

In that Top Flite has no control over the final assembly or material used for final assembly, no liability shall be 
assumed nor accepted for any damage resulting from the use by the user of the final user-assembled 
product. By the act of using the user-assembled product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is 
advised to return this kit immediately in new and unused condition to the place of purchase.

To make a warranty claim send
the defective part or item to
Hobby Services at this address:

Include a letter stating your name, return shipping address, as much contact information as possible (daytime 
telephone number, fax number, e-mail address), a detailed description of the problem and a photocopy of the 
purchase receipt. Upon receipt of the package the problem will be evaluated as quickly as possible.

Hobby Services

3002 N. Apollo Dr. Suite 1
Champaign IL  61822  USA

Technical Assistance Call

(217) 398-8970

[email protected]

SPECIFICATIONS

INSTRUCTION

MANUAL

[email protected]

Top Flite Models  Champaign, IL
Ph: (217) 398-8970, Ext. 5
Fax: (217) 398-7721

Wingspan:

36 in [ 915 mm]

Wing Area:

329 sq in  [ 21.2 dm

2

Weight:

27– 30 oz [ 765 – 850 g]

Wing

Loading:

11.8 – 13.1 oz/sq ft
[36 – 40 g/dm

2

]

Length:

34.5 in [875 mm]

Radio:

4 channel

Motor:

RimFire .10

Summary of Contents for Mini Contender Ep

















Reviews: