Hitachi Summit RAC-70YH5 Service Manual Download Page 7

Page: 7 / 102

– 5 –

above 50mm

above 100mm

above

0.45m

above 300mm

must not bend

above 100mm

2,300mm or more

Maximum pipe length 30m

Minimum pipe length 5m

above 200mm

above 700mm

above 200mm

above 50mm when
installed on the
ceiling of balcony

(

)

above 100mm

give clearance as
wide as possible

Plug

above 100mm

●

The difference in height
between the indoor and
outdoor unit should be kept
max 5m.

●

The connecting pipe, no
matter big or small, should
all be insulated with
insulation pipe and then
wrapped with vinyl tape. (The
insulator will deteriorate if it
is not wrapped with tape).

The connection of insulated
drain hose.

Please use insulated drain
hose for the indoor piping
(commercial product).

The indoor piping should be
insulated with the enclosed
insulation pipe. (If the insulator
is insufficient, please use
commersial products).

Be sure to
completely seal
any gap with putty.

CAUTION

The installation height of indoor unit must be 2.3m or more in a non public area.

Figure showing the installation of Indoor and Outdoor unit

0305E Pg 01-05

4/1/06, 10:47 AM

Summary of Contents for Summit RAC-70YH5







































































































Search results

Summary of Contents for Summit RAC-70YH5

Reviews:

Related manuals for Summit RAC-70YH5

Brands by name

Popular brands

Hitachi Summit RAC-70YH5, Service Manual

Search results

Summary of Contents for Summit RAC-70YH5

Reviews:

Related manuals for Summit RAC-70YH5

Brands by name

Popular brands