Hitachi Summit RAC-70YH5 Service Manual Download Page 24 | Manualshive

Page: 24 / 102

background image

– 22 –

ATTACHING THE AIR CLEANSING FILTERS

1

Open the front panel.

●

Pull up the front panel by holding it at both sides
with both hands.

2

Remove the filter.

●

Push upward to release the claws and pull out the
filter.

3

Attaching the air cleansing filters to the filter.

●

Attach the air cleansing filters to the frame by gently
compress its both sides and release after insertion
into filter frame.

4

Attach the filters.

●

Attach the filters by ensuring that the surface written
“FRONT” is facing front.

●

After attaching the filters, push the front panel at
three arrow portion as shown in figure and close it.

Cleaning and maintenance must be carried out only by qualified service personal. Before cleaning,
stop operation and switch off the power supply.

CAUTION

CAUTION

Do not bend the

air cleansing

filter as it may cause damage to
the structure.

NOTE

●

In case of removing the air cleansing filters, please follow the above procedures.

●

The cooling capacity is slightly weakened and the cooling speed becomes slower when the air
cleansing filters are used. So, set the fan speed to "HIGH" when using it in this condition.

●

Air cleansing filters are not washable and can be use in 1 year time. Type number for this air cleansing
filter is <SPX-CFH7>. Please use this number for ordering when you want to renew it.

●

Do not operate the air conditioner without filter. Dust may enter the air conditioner and fault may occur.

Claws

(4 places)

!

!

0305E Pg 16-27

4/1/06, 10:49 AM

22

«
...
22
23
24
25
26
...
»

Summary of Contents for Summit RAC-70YH5







































































































Reviews:

No comments

Related manuals for Summit RAC-70YH5

Brand: TCF Pages: 19

Brand: Haier Pages: 56

DELUXE HIGH WALL MINI SPLIT

Brand: ICP Pages: 26

4SCU 16LS Series

Brand: Armstrong Air Pages: 32

Brand: AERMEC Pages: 36

Brand: Olimpia splendid Pages: 12

Brand: GE Pages: 48

Brand: MAXA Pages: 48

Brand: Midea Pages: 15

Brand: GE Pages: 70

Brand: GE Pages: 60

Brand: Daikin Pages: 72

Brand: Daikin Pages: 35

Brand: Panasonic Pages: 44

Brand: Panasonic Pages: 52

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 63

Brand: Panasonic Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands