manualshive.com logo in svg

Hitachi H8/3670F-ZTAT HD64F3670, Hardware Manual

Share
Download
Hitachi H8/3670F-ZTAT HD64F3670 Hardware Manual Download Page 69

Rev. 1.0, 03/01, page 45 of 280

3.2.3

Interrupt Enable Register 1(IENR1)

IENR1 enables direct transition interrupts, and external pin interrupts.

Bit

Bit Name

Initial Value

R/W

Description

7

IENDT

0

R/W

Direct Transfer Interrupt Enable

When this bit is set to 1, direct transition interrupt requests
are enabled.

6

−

0

−

Reserved

This bit is always read as 0, and cannot be modified.

5

IENWP

0

R/W

Wakeup Interrupt Enable

This bit is an enable bit, which is common to the pins

WKP5

 to 

WKP0

. When the bit is set to 1, interrupt

requests are enabled.

4

−

1

−

Reserved

This bit is always read as 1, and cannot be modified.

3

IEN3

0

R/W

IRQ3 Interrupt Enable

When this bit is set to 1, interrupt requests of the 

IRQ3

 pin

are enabled.

2

−

0

−

Reserved

This bit is always read as 0, and cannot be modified.

1

−

0

−

Reserved

This bit is always read as 0, and cannot be modified.

0

IEN0

0

R/W

IRQ0 Interrupt Enable

When this bit is set to 1, interrupt requests of the 

IRQ0

 pin

are enabled.

When disabling interrupts by clearing bits in an interrupt enable register, or when clearing bits in
an interrupt flag register, always do so while interrupts are masked(I=1). If the above clear
operations are performed while I=0, and as a result a conflict arises between the clear instruction
and an interrupt request, exception handling for the interrupt will be executed after the clear
instruction has been executed.

Summary of Contents for H8/3670F-ZTAT HD64F3670


















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands