Hitachi H8/3670F-ZTAT HD64F3670 Hardware Manual Download Page 102 | Manualshive

Page: 102 / 305

background image

Rev. 1.0, 03/01, page 78 of 280

7.3.1

Boot Mode

Table 7-2 shows the boot mode operations between reset end and branching to the programming
control program.

1. When boot mode is used, the flash memory programming control program must be prepared in

the host beforehand. Prepare a programming control program in accordance with the
description in section 7.4, Flash Memory Programming/Erasing.

2. SCI3 should be set to asynchronous mode, and the transfer format as follows: 8-bit data, 1 stop

bit, and no parity.

3. When the boot program is initiated, the chip measures the low-level period of asynchronous

SCI communication data (H'00) transmitted continuously from the host. The chip then
calculates the bit rate of transmission from the host, and adjusts the SCI3 bit rate to match that
of the host. The reset should end with the RxD pin high. The RxD and TxD pins should be
pulled up on the board if necessary. After the reset is complete, it takes approximately 100
states before the chip is ready to measure the low-level period.

4. After matching the bit rates, the chip transmits one H'00 byte to the host to indicate the

completion of bit rate adjustment. The host should confirm that this adjustment end indication
(H'00) has been received normally, and transmit one H'55 byte to the chip. If reception could
not be performed normally, initiate boot mode again by a reset. Depending on the host's
transfer bit rate and system clock frequency of this LSI, there will be a discrepancy between
the bit rates of the host and the chip. To operate the SCI properly, set the host's transfer bit
rate and system clock frequency of this LSI within the ranges listed in table 7-3.

5. In boot mode, a part of the on-chip RAM area is used by the boot program. The area H'F780 to

H'FEEF is the area to which the programming control program is transferred from the host.
The boot program area cannot be used until the execution state in boot mode switches to the
programming control program.

6. Before branching to the programming control program, the chip terminates transfer operations

by SCI3 (by clearing the RE and TE bits in SCR3 to 0), however the adjusted bit rate value
remains set in BRR. Therefore, the programming control program can still use it for transfer
of write data or verify data with the host. The TxD pin is high(PCR22=1, P22=1). The
contents of the CPU general registers are undefined immediately after branching to the
programming control program. These registers must be initialized at the beginning of the
programming control program, as the stack pointer (SP), in particular, is used implicitly in
subroutine calls, etc.

7. Boot mode can be cleared by a reset. End the reset after driving the reset pin low, waiting at

least 20 states, and then setting the TEST pin and

NMI

pin. Boot mode is also cleared when a

WDT overflow occurs.

8.

Do not change the TEST pin and

NMI

pin input levels in boot mode.

«
...
100
101
102
103
104
...
»

Summary of Contents for H8/3670F-ZTAT HD64F3670


















































































































































































































































































































Reviews:

No comments

Related manuals for H8/3670F-ZTAT HD64F3670

Brand: Lab.gruppen Pages: 35

RocketLink-G 3088/I

Brand: Patton electronics Pages: 61

Brand: Raritan Pages: 4

Brocade X6-8 Director

Brand: Broadcom Pages: 207

FireWire 800 + Hi-Speed USB Combo

Brand: SIIG Pages: 20

Brand: Parker Pages: 50

Brand: Daedalon Pages: 6

Brand: ADTRAN Pages: 2

Brand: Glacier Pages: 2

Brand: ZKTeco Pages: 68

OPTIMA II CNPS10X

Brand: ZALMAN Pages: 20

Selenio SNP-GW-3GX32

Brand: Imagine communications Pages: 153

Threat Analysis Reporter TAR HL/SL/MSA

Brand: 8e6 Technologies Pages: 22

Brand: abaco systems Pages: 28

Brand: Crestron Pages: 8

Serial ATA PCI RAID

Brand: SIIG Pages: 36

Brand: Bosch Pages: 16

Brand: Bosch Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands