background image

Part Numbers 

© PRS 40 EZ  REV A 03/16/06 

190201_A 

51

 

20t (45k) RADIO LOAD CELL 
 

 

The load cell kit will include item 1, item 2, item 3, item 4, and one of the optional item 5. 
 

 

ITEM PART 

NUMBER  QTY  DESCRIPTION 

 

1 031-300-060-609 

1.00 

SENSOR ASSY, FORCE TRANS. 45K STRAIGHT 
W/TRANSMITTER 

 

2 031-300-060-558 

1.00 

BRACKET, H 20t RADIO LOADCELL  2-050-520 PLATES & 
2-050-573 

 

3 031-300-050-625 

2.00 HARDWARE, COTTER PIN 3/8" x 3" 

 4 

031-300-050-568 

1.00 

PIN, 2.25" FOR 40K RADIO LOADCELL 1-1/8" ROPE 

OPTION 5 031-300-050-568 

1.00 

PIN, 2.25" FOR 40K RADIO LOADCELL 1-1/8" ROPE 

OPTION 5 031-300-050-559 

1.00 

PIN/BUSHINGS, 2" FOR 40K RADIO LOADCELL 1" ROPE 

OPTION 5 031-300-050-600 

1.00 

PIN/BUSHINGS, 1 3/4" FOR 40 KRADIO LOADCELL 

OPTION 5 031-300-050-563 

1.00 

PIN/BUSHINGS, 1 5/8" FOR 40 KRADIO LOADCELL 7/8" 
ROPE 

OPTION 

031-300-050-604 

1.00 

PIN/BUSHINGS, 1 1/2" FOR 40K RADIO LOADCELL  

*  Please contact Hirschmann, ECS with questions concerning 
   repair or replacement of component.  (717) 263-7655 

Summary of Contents for PRS 40 EZ


























































Reviews: