manualshive.com logo in svg

Hirschmann MS30, Power MICE, MACH 4000, OCTOPUS, User Manual

Share
Download
Hirschmann MS30, Power MICE, MACH 4000, OCTOPUS User Manual Download Page 9

About this Manual

Layer 2 Enhanced with Layer 2 Professional

Release 1.0 10/05

9

About this Manual

The “Basic Configuration” user manual contains all the information you need 
to start operating the switch. It takes you step by step from the first startup 
operation through to the basic settings for operation in your environment.

The following thematic sequence has proven itself in practice:

D

Set up device access for operation by entering the IP parameters

D

Check the status of the software and update it if necessary

D

Load/Save the configuration

D

Configure the ports

D

Set up protection from unauthorized access

D

Optimize the data transmission with network load control

D

Synchronize system time in the network

D

Function diagnosis

The “Installation” user manual contains a device description, safety instructions, 
a description of the display, and all the other information that you need to install 
the device before you begin with the configuration of the device.

The “Redundancy Configuration” user manual contains all the information 
you need to select a suitable redundancy procedure and configure it.

You will find detailed descriptions of how to operate the individual functions in 
the “Web-based Interface” and “Command Line Interface” reference manuals

If you use Network Management Software HiVision you have further 
opportunities to:

D

have an event logbook.

D

configure the „System Location“ and „System Name“.

D

configure the network address range and SNMP parameters.

D

save the configuration on the Switch.

D

simultaneous configuration of several Switches.

D

configure the relevant ports to be displayed red if there is no link state.

Summary of Contents for MS30, Power MICE, MACH 4000, OCTOPUS





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands