background image

10.  Fail Safe

The Door Top Alarm includes a failsafe system, where the alarm will sound if there is a power 
cut or a wire breakage. NOTE - this is only applicable if the staff attack system has been 
wired into the Normally Closed terminals in the Hipac electronics box. It is possible to get 
notification if the Normally Open terminals have to be used but this will not be an audible 
alarm and is dependent on your staff attack company being able to send a failure message 
back to say the main control panel at the nurses’ station.
The hinge is supplied in 2 pieces, the main section of the hinge which takes most of the 
doors weight and the electrically modified section, at the top, which has the cables running 
through it. The reason for this is for ease of service, so if at any time there is a problem, the 
electrically modified piece can simply be taken out without having to take the door off.
The wiring to the electronics box should be checked (and signed off at each stage on 
the supplied sign off sheet) with the tester box at each stage during installation by the 
contractor.

5 Seconds

10 Seconds

20 Seconds

30 Seconds

Summary of Contents for 120120



















Reviews: