PCM412 - Manuale per l'utente
28
29
Opens and closes
after pause
And opens only door1
closed after
pause
Prevents the opening Prevents the opening Prevents the opening
Continuous opening
Continuous opening
Without the gate.And
wait command
start to continue
the opening
Stop motion.
Disengagement
incorporates open
Not effect
Prolongs the time
until the issue
Not effect
Let the gate
open. Restoration
closes not wait
pause
Prevents
reclosing
Prevents
reclosing
Stop the closure and
reopens
Stop the closure and
reopens
immediately
Stop motion
and restoration
awaits further
command
closing
Without the gate
and reopens to the
disengagement
Without the gate and
reopens
immediately
Automatic condominium
ON
1
2
3
4
5
6
7
8
Delay times of 4 seconds
ON
1
2
3
4
5
6
7
8
Delay times of 8 seconds
ON
1
2
3
4
5
6
7
8
Door hammering disabled
ON
1
2
3
4
5
6
7
8
Door hammering enabled
ON
1
2
3
4
5
6
7
8
Output fixed
Output intermittently
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
FX40D / FX55D
FX30D
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
Automatic
ON
1
2
3
4
5
6
7
8
Opens and closes
after
pause
And opens only anta1
closed after
pause
Prevents the opening Prevents the opening Prevents the opening
Without openness
and closes
immediately
Without openness
and closes
immediately
both wings
Without the gate and
restoration expected
further control start
to continue opening
Stop motion.
Disengagement
incorporates open
Not effect
Not effect
Not effect
Let the gate
open. Restoration
closed without
wait time
IPrevents
reclosing
Prevents
reclosing
Stop the closure and
reopens
immediately
Stop the closure and
reopens
immediately
Stop motion
and restoration
awaits further
command for
closing
Without the gate
and reopens to the
disengagement
Without the gate
and reopens
immediately
Double door
Single door
ON
1
2
3
4
5
6
7
8
ON
1
2
3
4
5
6
7
8
3.2.2
Closing wing timing
Setting button 3 in one of the two position as shown in the figure, you can adjust the range of
closing delay for the second door (driven by motor 2, without solenoid) compare the first one. This is
very useful when the first door closes slowly to avoid overlap as it will go wrong
3.2.3 Door
hummering
Placing the button 4 as shown “ hammering active", the opening of the gate will be achieved
opening by a closing pusch( for a few second) from the ratiomotor on the door that contains the
solenoid.
3.2.4 Warning
light
By dip-switches 5,the output of flash can be set either fixed to use traditional warning light,or
Intermittently for strobes
3.2.5
Double or single doors
By dip-switches 7,you can enable the operation of a single geared motor for a door or both geared
motor for a double-door gate.
3.2.6
Type of photocells
The central PCM412 can use both traditional photocell relay type FX40D / FX55D and
pulse-type photocells with self diagnosis FX30D.Setting button 8 as illustrate you can set different
types of photocells. . In the absence of power for
batteries, photocells are switched off when the gate is closed and switch on just before putting
moving the gate.
This involves a slight delay between the command and start the motion of the gate
CLOSING
GATE
STATUS
CLOSE
OPENING
FTC. Internal
FTC. External
START 1
START 2
PAUSE
STOP
CLOSING
GATE
STATUS
CLOSE
OPENING
FTC. Internal
FTC. External
START 1
START 2
PAUSE
STOP
Programmation
