Mode
Data
Original operating instructions
Safety and warning notices
In
Tra6
3, In
Tra6
3.LVAC
«Data» button
➔
The electrical connection may only be set up by an electrician.
➔
The arrangement of the components depends on the structural conditions and the gate design.
➔
Switch off the operating voltage before working on the system.
➔
The switching device may only be used to protect against dangers at crushing and shearing points on automatic sliding gates (designated use).
Any other use is prohibited.
➔
Use of components not supplied by Bircher-Reglomat (including safety edges) will render the guarantee and liability null and void.
Switching device with inductive transmission system used in combination with safety edges to
avoid dangers at crushing and shearing points in sliding gate systems.
Operation
Display
Info
3
Control buttons
on device:
«Mode» button
Please keep for future reference!
E
N
G
LI
S
H
– CLOSE output is deactivated
– No current flow
➔
OK
– Current flow
➔
error
«Data» Taste drücken
– No current flow
➔
consumer missing
– CLOSE output is activated
– Current flow
➔
OK
1
1
1
Diagnose-Modus
5
Press the
«
Mode
»
and
«
Data
»
buttons simultaneously for 2 s
➔
status LED flashes orange. Press
«
Mode
»
buttons briefly to change to the next
mode. Press the
«
Mode
»
button for 2 s to exit diagnostic mode.
1
– OPEN output is deactivated
– No current flow
➔
OK
– Current flow
➔
error
Press the «Data» button
– No current flow
➔
consumer missing
– OPEN output is activated
– Current flow
➔
OK
2
2
2
2
Mode «C» current configuration
Mode «e» current fall-delay time
Displays current configuration of
safety edge inputs, see configura-
tion table.
Configuration
➔
chapter 6
Displays current fall-delay time,
see fall-delay time table.
Configuration
➔
chapter 6
– Both outputs deactivated
– No current flow
➔
OK
– At least 1 output with current flow
➔
Error, press the «Data» button
– At least 1 output without current flow
➔
Consumer missing
– Both outputs are activated
– Current flow
➔
OK
1
2
1
2
1
2
Mode «S» Both outputs
1
2
1
2
CLOSE Output
OPEN Output
Mode
Data
Dots
= Display flashes
System components
1
1
5
7
9
3
4
4
3
22
7
6
9
5
1
Hole
grey
Hole
red
Mobile safety edge CLOSE
(primary closing edge)
INTR-MOB62, converter for
mobile safety edge
Mobile safety edge OPEN
INTR-FIX60, coil
Stationary safety edge CLOSE
InTra6 3, switching device
Stationary safety edge OPEN
Steel cable (see chapter 9.3)
INTR-MOB61, converter for
safety edge
Open
Open
Close
Close
Electrical connection and terminal diagram
2
Version
Operating
voltage
Stationary safety
edge CLOSE
Stationary safety
edge OPEN
Test input
Coil
connection
Output
CLOSE
Output
OPEN
InTra6 3
InTra6 3.LVAC
+/~
–/~
A1
A2
1
2
3
4
T1
T2
+
TX
BN
WH
GN
YE
RX
14
11
21
24
When everything is connected correctly:
Display after switching on:
Status LED lights up green
1
2
1
2
4
Dots
flash
Displays shown when safety edge is actuated: Status LED leuchtet orange
actuated:
actuated:
actuated:
actuated:
Standard operation
Mode «r» Resistance
Mode «S» Simulation CLOSE
Mode «S» Simulation OPEN
Error display mode
The 5 most recent errors
can be interrogated.
The resistances of the
safety edges are displayed
Press the
«
Data
»
key briefly in
each case, and the errors are dis-
played one after the other. End
appears when the
«
Data
»
button
is pressed for the 5th time. The
malfunctions are displayed in
chronological order (new
➔
old)
Example:
8 = Resistance between
7 and 9 kohm.
1 = safety edge
To access the next safety edge:
Press the
«
Data
»
button
