background image

c

 

BETCO DOOR SYSTEMS 

INSTALLATION INSTRUCTION & OWNERS MANUAL  

                                    SAFETY TIPS 

 

1.

Read entire instructions carefully before 

        installing door. 

 

2.

Installation, adjustments and repairs must be  

                 performed by an experienced, trained professional 

                 door installer. 

 

3.

Use proper lifting equipment and lifting procedures  

                 when installing door in opening. 

 

4.

Do not cut retention band around door roll or unwrap 

                 protective wrapper until instructions indicate. 

 

5.

Do not stand in door opening during 

                 operation of door. 

 

6.

Do not allow anyone other than authorized 

                 installers to adjust or install. 

 

7.

If door becomes inoperative or hard to  

                 operate, contact a qualified door agency. 

 

 

 

 

 

 

WARNING 

THE FOLLOWING INSTRUCTIONS ARE A GUIDE  

FOR PROFESSIONAL DOOR INSTALLERS,  

SERIOUS INJURY MAY RESULT IF  

INEXPERIENCED PERSONNEL 

ATTEMPT TO WORK ON THIS PRODUCT 

ITEM 

DESCRIPTION 

PART NO. 

NOTES 

DOOR CURTAIN 

DP6-WITH HEIGHT COLOR 

ORDER BY OPENING WIDTH, HEIGHT & COLOR 

DOOR TRACK, LEFT 
DOOR TRACK, RIGHT 

DTA-HEIGHT-DL 
DTA-HEIGHT-DR 

ORDER BY DOOR OPENING HEIGHT 

DOOR AXLE ASSEMBLY 

DB-WIDTH-2D OR 3D 

ORDER BY DOOR OPENING WIDTH 

DOOR LATCH BASE 
DOOR LATCH SLIDE 

D20006 
D20007 

NONE 

DOOR EXTRUSION ASSEMBLY 

DX-WIDTH-AL 

ORDER BY DOOR OPENING WIDTH 

DOOR STIFFENER CHANNEL 

DS-WIDTH-GL 

ORDER BY DOOR OPENING WIDTH 

DOOR ASTRAGAL 

D20008 

NONE 

DOOR BRACKET, LEFT 
DOOR BRACKET, RIGHT 

D20005 
D20004 

NONE 

DOOR BRACKET ASSEMBLY 

 

WITH DOOR BRACKET ADAPTER 

DOOR STOP 

D20002 

NONE 

DOOR HANDLE 

D20009 

NONE 

TENSION ADJUSTER 

D20017 W/BEARING 
D20018 W/O/BEARING 

OPTIONAL-ORDER W/BEARING OR  
W/O/BEARING AT TIME OF ORIGINAL ORDER 

FELT SEPARATOR STRIP 

D20028 

NONE 

HARDWARE  PACKAGE 

STEEL CONSTRUCTION 

ORDER BY BUILDING CONSTRUCTION 

HARDWARE  PACKAGE 

WOOD OR MASONRY CENTER 

ORDER BY BUILDING CONSTRUCTION 

DOOR CURTAIN DAMPENER 

D20028 

NONE 

WARNING LABEL 

BETCO LABEL 

(OUTSIDE DOOR) 

    Page 1      12/31/03 

Summary of Contents for DOOR SYSTEMS










Reviews: