![background image](http://html1.mh-extra.com/html/hilti/gx-100-e/gx-100-e_operating-instructions-manual_2136118022.webp)
18
en
-WARNING-
G
Driving the nail may cause flying frag-
ments.
G
Flying fragments may injure parts of
the body or the eyes.
G
Wear eye protection and a hard hat.
GX 100
GX 100
R
-WARNING-
G
Making the tool ready to fire by press-
ing it against a part of the body (e.g.
the hand) is not permissible.
G
This could cause a nail to be driven
into a part of the body.
G
Never press the tool against a part of
the body.
-CAUTION-
G
The nail is driven by the energy released
on ignition of a gas-air mixture.
G
An excessively high noise level may
damage the hearing.
G
Wear ear protection.
7. Operation
-NOTE-
When holding the tool with the second hand, care must
be taken to position the hand so that no ventilation slots
or openings are covered.
-CAUTION-
Never attempt to redrive the same fastener.
7.1 Operation
-NOTE-
The magazine must contain at least 2 nails, otherwise no
nail can be driven.
1. Hold the tool at right angles to the work surface and
then press it against the surface as far as it will go.
2. Drive the fastener by pulling the trigger.
7.2 The magazine
-NOTE-
The tool must be unloaded each time before the maga-
zine is changed (see 7.6).
7.2.1 Removing the magazine
1. Pull the nail pusher back until it engages.
-NOTE-
The nail pusher must engage correctly.
2. Remove all nails from the magazine.
3. Disengage the nail pusher and allow it to slide forward
slowly.
4. Push the locking lever down toward the magazine.
5. Swing the magazine forwards away from the tool.
6. Detach the magazine from the tool.
7.2.2 Fitting the magazine
1. Attach the front end of the magazine to the tool.
-NOTE-
The locking lever must be in the open position.
2. Swing the magazine toward the tool, taking care to
ensure that its contours match the shape of the tool.
3. Close the locking lever and check that it engages
securely.
7.3 Nosepiece
7.3.1 Removing the nosepiece
1. Press the lockbutton and turn the nosepiece of the tool
in the opposite direction to the arrow.
2. While pressing the lockbutton, pull the nosepiece away
from the tool.
7.3.2 Fitting the nosepiece
1. Bring the nosepiece lockbutton into alignment with
the notch on the tool.
2. Slide the nosepiece onto the tool into the end posi-
tion.
3. Turn the nosepiece in the direction of the arrow until
it engages.
7.4 Support
7.4.1 Fitting the support
1. Push the support at right angles into the slot in the
magazine.
2. Pivot the support through 90° and engage it in posi-
tion.
7.4.2 Removing the support
1. Release the support by pressing the spring catch.
2. Pivot the support through 90°.
3. Pull the support away from the magazine at right
angles.
7.5 Bringing the piston into the correct position
-NOTE-
The piston is incorrectly positioned when the nosepiece
of the tool has not extended to its original position after
the tool is lifted away from the work surface.
Printed: 07.07.2013 | Doc-Nr: PUB / 5069872 / 000 / 00
Summary of Contents for GX 100-E
