![background image](http://html1.mh-extra.com/html/hilti/gx-100-e/gx-100-e_operating-instructions-manual_2136118025.webp)
21
en
Piston in wrong position
Tool is too hot
Free the mechanism by pressing the reset
button
. Drive the next nail (the tool may
fire once without driving a nail after resett-
ing). Allow the tool to cool if necessary.
Gas can almost empty
Use a new gas can
(fit the valve head to the new can).
Tool doesn’t fire
Gas can almost empty
Insert a new gas can.
Valve head is defective
Fit a new valve head on a new gas can.
Valve head fitted incorrectly / not
Fit the valve head to the can correctly.
fully seated
Gas can not inserted correctly in the
Insert the gas can in the tool correctly.
tool
Operating temperature too low
Use a gas can that has been warmed
to room temperature (~20°C / ~68°F)
Ferromagnetic foreign objects
Remove foreign objects from the
adhering to the magazine
magazine.
Magazine is defective
Try using another magazine.
Valve head does not dispense the
Remove the gas can and allow it to
correct gas quantity
cool or operate the valve head manually
several times (press the white plate toward
the valve head) until it functions correctly.
-WARNING-
Never point the nozzle toward persons, ani-
mals, naked flames or hot objects).
Electronics defective
If electronics are defective, no
immediate remedy is possible. Have
the tool repaired at a Hilti repair center.
-CAUTION-
Wait 10 seconds and then, if possible, remove the gas can and valve head from the tool before manipulating the
tool as described in the instructions below (*).
Nail jammed in the
Several nails driven on top of each
* Remove the magazine and nosepiece and
fastener guide
other
pull the nail out toward the front.
* Remove the nosepiece and tap the nail
back with a hammer and pin punch.
Nail jammed in the
Nail has become jammed during
* Remove the magazine.
“guide” (steel part
the driving operation
Remove the nail.
of the magazine)
Tool cycling mechanism
Piston in wrong position
* See “Piston in wrong position”
jammed (no movement of Nail jammed under the button
* Remove magazine, remove nail.
nosepiece after lifting tool
-CAUTION-
away from work surface)
Do not damage the button and nail detector
Nail detector jammed (possibly
* Pull the nosepiece forward
due to dirt or debris)
by hand or use pliers.
Trigger jammed in rearmost position
* Bring the trigger into its outset
position (by hand or use pliers).
Loose nails / foreign objects
* Remove the magazine, remove
under the cover
foreign objects. Have the tool
repaired at a Hilti repair center.
Gas can cannot be
Tool cycling mechanism jammed
Remove the magazine. Remove the nail.
removed
Open the cover of the gas can compartment
and press the valve head toward the outside,
in the direction of the arrow, until the valve
head is released from the can. Remove the
valve head and the gas can individually.
Printed: 07.07.2013 | Doc-Nr: PUB / 5069872 / 000 / 00
Summary of Contents for GX 100-E
