4. Technical data
Tool with magazine and gas can
Weight
3.80 kg
(8.37 lbs)
Dimensions (L
×
W
×
H)
425
×
172
×
330 mm
(16
3
/
4
″×
6
3
/
4
″×
13
″
)
Nail length
max. 39 mm
max. (1
9
/
16
″
)
Nail diameter
3.0 mm
(
쏗
118 in)
Magazine capacity X-GM 20
20 + 2 nails
Contact movement
approx. 36 mm
(1
7
/
16
″
)
Contact pressure
approx. 120 N
(27 lbs)
Operating temperature range / ambient temperature
–5°C to 45°C
(23°F to 113°F)
Max. fastener driving rate
600 per 30 min.
1000 per hour
Noise information
(applicable to 1mm sheet metal on B45 concrete):
1b) Noise (power) level L
WA, 1S
109 dB (A)
Workplace-relevant emission value L
pAImax
102 dB (A)
(measured at operator ear level)
1e) Noise (pressure) level L’
–
pA, 1s
96 dB (A)
(Variations in operating conditions may cause deviation from these noise emission values.)
Gas can
Capacity
1 can for 750 nails
Recommended transport and storage temperature
+5°C to +25°C
(41°F to 77°F)
The gas can is pressurized.
Avoid prolonged exposure to direct sunlight.
Never expose the gas can to temperatures over 50°C (122°F).
Substances contained
Dimethyl ether, isobutane, propylene,
propane, butane, ethanol and isoparaffin
Gas can
Not refillable
Right of technical changes reserved.
15
en
5. Safety precautions
5.1 Basic safety instructions
In addition to the safety precautions listed in the indi-
vidual sections of these operating instructions, the fol-
lowing points must be strictly observed at all times.
5.2 Use as intended
The tool is intended mainly for professional use. It designed
for driving nails into concrete, steel, sand-lime block, con-
crete block masonry and masonry with a plaster or cement
rendering finish when installing electrical and mechani-
cal installations and for other suitable fastening applica-
tions in the construction industry and associated trades.
G
Manipulation or modification of the tool is not per-
missible.
G
To avoid the risk of injury, use only original Hilti acces-
sories and consumables.
G
Observe the information printed in the operating instruc-
tions concerning operation, care and maintenance.
G
Never point the tool at yourself or at any bystander.
G
Never press the nosepiece of the tool against your hand
or other part of your body (or other person’s hand or
parts of their body).
G
Do not attempt to drive fasteners into unsuitable mate-
rials:
- Materials that are too hard, e.g. welded steel and cast
iron
- Materials that are too soft, e.g. wood and drywall
panel
- Materials that are too brittle, e.g. glass and ceramic
tiles
Driving a nail into these materials may cause the nail
to break, shatter or to be driven right through.
Printed: 07.07.2013 | Doc-Nr: PUB / 5069872 / 000 / 00
Summary of Contents for GX 100-E
