![background image](http://html1.mh-extra.com/html/hilti/dx-9-enp/dx-9-enp_original-operating-instructions_2136108043.webp)
*2241307*
2241307
English
35
1. Stand the tool on its grip.
2. Press the magazine release button (red button) on the magazine and allow the magazine to slide down.
3. Rotate the base plate in a counter clockwise direction, until the connection is released.
4. Lift off the base plate.
7.3
Fitting the base plate
1. Make sure that the piston stopper is correctly fitted in the base plate and that the piston guide and the
piston are correctly seated in the tool.
2. Press the base plate against the thread.
3. Rotate the base plate in a clockwise direction as far as it will go.
4. Rotate the base plate back slightly until it is in its starting position relative to the magazine.
5. Push the magazine back until it engages with the base plate.
7.4
Cleaning the fastening tool
WARNING
Risk of injury!
Cartridges in the tool could fire (explode).
▶
Check that all cartridges have been removed from the tool before carrying out the following tasks with
the tool.
CAUTION
Risk of burns!
Parts of the tool may be very hot after the tool has been in use.
▶
If it is necessary to carry out maintenance without first allowing the tool to cool down, it is essential that
protective gloves are worn.
1. Disassemble the base plate. → page 34
2. Pull the catch out and hold it in this position. Pull the piston out of the piston guide and then release the
catch.
3. Pull the piston stopper out of the base plate. If necessary, use the piston to lever the piston stopper out
of the base plate.
4. Pull the catch out and hold it in this position. Pull the piston guide upwards out of the tool and then
release the catch.
5. Clean the inside of the tool. Then stand the tool upside down and tap it firmly with your hand so that the
dirt falls out.
6. Use the large accessory wire brush to clean the surfaces of the piston guide (see marked area).
7. Use the small round brush to clean the cartridge chamber and the adjoining holes for the power regulation
pin.
8. Use the narrow round brush to clean the cartridge guideway.
9. Use
Hilti
lubricant spray to lubricate the moving parts of the fastener strip guides.
Use of other lubricants may damage the rubber parts, especially the piston stopper. Moreover,
other lubricants may cause dust to adhere to parts of the tool resulting in a build-up of deposits.
10. Slide the piston guide into the tool from above, until the catch engages.
11. Pull out the catch and hold it in this position. Insert the piston, pushing it in until the tip of the piston no
longer projects beyond the end of the tool, and then release the catch.
12. Insert the piston stopper (rubber part to the front) into the base plate.
13. Fit the base plate. → page 35
14. Press the reset button for at least 1 second to reset the counter for the number of fasteners driven until
the next scheduled cleaning operation is due.
15. Check that the tool is ready for use. → page 30
Summary of Contents for DX 9-ENP
