![background image](http://html1.mh-extra.com/html/hilti/dx-9-enp/dx-9-enp_original-operating-instructions_2136108038.webp)
30
English
2241307
*2241307*
Peak sound pressure emission level (L
pC, peak
)
137 dB(C)
Uncertainty for the peak sound pressure level (K
pCpeak
)
2 dB(C)
4.3
Vibration
The vibration value that must be specified in accordance with 2006/42/EC does not exceed 2,5 m/s².
5
Preparations at the workplace
5.1
Establishing the position of the fasteners
To avoid incorrectly driven fasteners, proceed as follows:
▶
Each time you lay a metal sheet in position on the steel beams, use a water-resistant pen to mark the
area in which fasteners can be driven.
Do this each time, for each individual metal sheet. It is not sufficient to simply mark the ends of
the beam and then draw a straight line between these points as the supporting beams may be
distorted, i.e. curved.
5.2
Checking that the tool is ready for use
This check should always be carried out immediately before use of the fastening tool and after
reassembling the tool after cleaning or after a routine check of the condition of the piston and piston
stopper.
1. Make sure that there are
no cartridge strips and no nail strips
in the tool.
@
Catch
;
Pressure pin
=
Slider
%
Nosepiece
2. Check the fastening tool for visible signs of damage,
especially to the components shown in the illustra-
tion.
Result
Visible signs of damage are found
▶
Have the tool repaired by
Hilti
Service.
3. Press the tool against the working surface until a definite resistance is felt and then check the position of
the pressure pin.
Result 1 / 2
The pressure pin is not pressed down – the spring on the pressure pin is not compressed.
The tool has detected no nail and thus cannot be pressed against the working surface. The tool is
working correctly.
Result 2 / 2
The pressure pin is pressed all the way down, the spring on the pressure pin is compressed and a click
is heard when the trigger is pressed.
The slider may be jammed. The tool should be cleaned again and the test repeated. If the problem
persists, the tool must be repaired by
Hilti
Service.
4. Release any pressure on the tool.
5. Load the nail strips → page 31, but
do not load any cartridge strips
.
Summary of Contents for DX 9-ENP
