![background image](http://html1.mh-extra.com/html/hilti/dx-9-enp/dx-9-enp_original-operating-instructions_2136108046.webp)
38
English
2241307
*2241307*
Trouble or fault
Possible cause
Action to be taken
The cartridges are not trans-
ported.
The tool is damaged.
▶
Contact
Hilti
Service.
The cartridge strip cannot be
removed.
The tool is damaged.
▶
Contact
Hilti
Service.
The tool doesn’t fire.
Misfire
▶
Remedy the malfunction.
The cartridge strip is used up.
▶
Remove the cartridge strip from
the tool.
▶
Insert a new cartridge strip.
There are less than 15 fasteners in
the tool.
▶
Load new fastener strips.
The tool is not adequately com-
pressed.
▶
Press the nose of the tool
against the working surface
again and pull the trigger.
Fastener transport malfunction.
▶
Check that the fastener strips
are free to move.
▶
Remove any damaged or
defective cartridge strips or
strips containing damaged or
defective fasteners.
The tool is clogged with dirt.
▶
Clean the tool.
The cartridges are unsuitable.
▶
Contact
Hilti
Service.
▶
Do not attempt to forcibly
remove cartridges or the
cartridge strip.
The tool is damaged.
▶
Contact
Hilti
Service.
Insufficient nail stand-off
The fastener missed the beam.
▶
Mark the position of the beam
and drive another fastener.
Driving power is too high.
▶
Reduce the driving power
(adjust the power regulation) or
use less powerful cartridges – if
available.
The piston is worn.
▶
Change the piston and piston
stopper together (as a set).
The wrong piston has been fitted.
▶
Check that the right piston /
fastener combination is used.
Space between metal sheet
and profile.
Space between metal sheet and
profile
▶
Avoid gaps between profile and
beam, or secure the beam on
the correct side.
Metal sheet is deformed
Beam missing as sub-structure
▶
Mark the beam at the correct
position before positioning
the power tool for driving the
fastener.
Excessive nail stand-off
The fastener is too close to the
edge of the beam.
▶
Mark the position of the beam
and drive another fastener.
Driving power is too low.
▶
Increase the driving power
(adjust the power regulation) or
use more powerful cartridges –
if available.
The tool is clogged with dirt.
▶
Clean the tool.
The piston is broken.
▶
Change the piston and piston
stopper together (as a set).
Summary of Contents for DX 9-ENP
