![background image](http://html1.mh-extra.com/html/hilti/dst-wrc-ca/dst-wrc-ca_manual_2136277016.webp)
14
English
2053441
*2053441*
3. Use <<OK>> to reset the remote control unit to the factory default settings or exit the screen with
<<Cancel without saving>>.
◁
The pairing information for the partner device is not deleted.
6
Manual operation
6.1
Overview
In manual-mode cutting the operator makes all the settings, both before and during cutting.
Measure the outside diameter of the saw blade before installing it. The diameter you enter influences blade
speed of rotation and depth and length of the cut. Installation of the rail, choice of country and system
tolerances influence depth and length of the cut.
Note that the actual depth and length of cut can differ considerably from the values shown or set.
6.2
Cutting with the wall saw in manual mode
1. Press the
ON/OFF
button.
◁
The button lights up green and the
Home
screen appears on the display.
◁
The remote control unit is ready for use.
2. Select <<Manual mode>>.
◁
The
Saw blade
screen appears on the display.
3. Use the control knob to select the saw blade diameter.
4. Position the saw head for the start.
◁
To do so, push the joystick up or down and hold it in this position, while at the same time using the
control knob to set the advance speed.
You can also change the setting for the saw-blade diameter by turning the control knob without
pushing the joystick at the same time. If you hold the joystick in one position for about five
seconds the advance movement is accepted as the setting for constant advance. This applies
only to advance, not to cutting depth. You can release the joystick and allow the saw to travel to
the intended position.
Briefly move the joystick as soon as the saw head reaches the desired position.
5. Press the
DRIVE ON/OFF
button.
◁
The drive of the saw blade starts.
6. If automatic cooling water control is not activated, turn on the cooling water with <<Turn cooling water
ON>>.
7. Move the joystick to the left or right to start cutting and at the same time turn the control knob to adjust
performance. Release the joystick as soon as the saw blade has reached the desired cutting depth. The
calculated cutting depth is shown on the display on the remote control unit.
8. Push the joystick up or down to move the saw head along the rail and turn the control knob as necessary
to adjust performance.
9. At the end of the cut, briefly move the joystick to stop the saw's advance.
10. Repeat steps seven through nine until the desired total depth of cut is reached.
11. Use the joystick to pivot the saw blade out of the cut to the 12 o’clock position.
12. Press the
DRIVE ON/OFF
button.
◁
The drive of the saw blade stops.
13. If automatic cooling water control is not activated, turn off the cooling water with <<Turn cooling water
OFF>>.
14. Move the saw head to a position in which it can easily be removed.
15. Press the
EMERGENCY STOP
button.
7
Assisted operation with Cut Assist
7.1
Overview
This remote control unit features the
Cut Assist
function. It automates various work steps.
When you select the
Cut Assist
function, you are prompted to set the parameters necessary for making the
cut. Once you have entered the necessary values and started the saw-blade drive, the cut is made to a very
large extent without any further intervention on your part.
Printed: 28.02.2018 | Doc-Nr: PUB / 5200714 / 000 / 03
Summary of Contents for DST WRC-CA
Page 1: ...DST WRC CA English Printed 28 02 2018 Doc Nr PUB 5200714 000 03...
Page 2: ...Printed 28 02 2018 Doc Nr PUB 5200714 000 03...
Page 21: ...Printed 28 02 2018 Doc Nr PUB 5200714 000 03...
Page 22: ...Printed 28 02 2018 Doc Nr PUB 5200714 000 03...