background image

12 

 

Attribute  Description 

Short-haul 

Multimode 

Optical 

Module 

(850nm) 

Medium-

haul Single-

mode 

Optical 

Module 

(1310nm) 

Long-haul 

single-mode  

optical 

module 

(1310nm) 

 

Medium-haul 

Single-mode 

Optical 

Module 

(1310nm) 

Long-haul 

Single-mode 

Optical 

Module 

(1310nm) 

Long-haul 

Single-mode 

Optical 

Module 

(1550nm) 

Ultra-long-

haul Single-

mode Optical 

Module 

(1550nm) 

Central 

Waveleng

th 

850nm 

1310nm 

1310nm 

1550nm 

1550nm 

1310nm 

1550nm 

1550nm 

Optional 

Original 

Hillstone 

Optical 

Module 

TRAN-

SX 

TRAN-

LX10 

TRAN-

LX40 

 

TRAN-

LX80 

TRAN-

LX40 

 

TRAN-LX80 

Notes: The original Hillstone optical module should not be used together with optical modules from 
other manufacturers, otherwise some errors may occur. 

If an SFP copper module is applied to an SFP port, you should use a crossover or straight-through 
cable (i.e. standard Ethernet cable). Attributes for the SFP copper module are shown in the table 
below: 

Table: SFP Copper Module Attributes 

Attribute 

Description 

Connector 

RJ-45 

Port Standard 

Auto-MDI/MDIX (crossover cable and straight-through cable 
autosensing) 

Maximum 
Transmission 
Distance 

100m 

Negotiation 
Mode 

10/100/1000Mbps autosensing (some only supports 1000Mbps) 

Full/half-duplex 

Summary of Contents for A200 Series




























Reviews: