HIKVISION iDS-8104AHQXLI-E4 User Manual Download Page 118

Page: 118 / 224

ATM Digital Video Recorder User Manual

117

Step 5

Select video files from the

Chart

List

interface to export.

Figure 7-9

Result of Event Search

Step 6

Export the video files. Please refer to step 5 of

Chapter 7.1.2 Backing up by Normal

Video/Picture Search

for details.

7.1.4 Backing up Video Clips

Purpose

You may also select video clips in playback mode to export directly during Playback, using USB
devices (USB flash drives, USB HDDs, USB writer), or SATA writer.

Step 1

Enter

Playback

interface.

Step 2

During playback, use buttons

in the playback toolbar to start or stop clipping

record file(s).

Step 3

Click

to enter the file management interface.

Figure 7-10

Video Clips Export Interface

Summary of Contents for iDS-8104AHQXLI-E4

































































































































































































































Search results

Summary of Contents for iDS-8104AHQXLI-E4

Reviews:

Related manuals for iDS-8104AHQXLI-E4

Brands by name

Popular brands

HIKVISION iDS-8104AHQXLI-E4, User Manual

Search results

Summary of Contents for iDS-8104AHQXLI-E4

Reviews:

Related manuals for iDS-8104AHQXLI-E4

Brands by name

Popular brands