manualshive.com logo in svg

HIKVISION DS-PK00 series, User Manual, Page: 17 / 63

Share
Download
HIKVISION DS-PK00 series User Manual Download Page 17

Network Security Control Panel User Manual 

11 

 

LCD Keypad Displayed Information 

The  system  status  display  demonstration  indicates  the  keypad  display  interface  of  system 
status without any key pressing.     

Powering on Display Demonstration 

The display demonstration after powering on is shown below. 

HIKVISION

 

System Status (normal) Display Demonstration 

The display demonstration of system status (working properly) is shown below.   
Global Keypad   

SYS1D    SYS2R    SYS3A    SYS4R

SYS5R    SYS6R    SYS7R    SYS8R

 

  The system status description is shown below. 

 

System Status 

Description 

SYS1D 

Partition1 Disarmed 

SYS2R 

Partition2 Ready 

SYS3A 

Partition3 Armed 

SYS4R 

Partition4 Ready 

SYS5R 

Partition5 Ready 

SYS6R 

Partition6 Ready 

SYS7R 

Partition7 Ready 

SYS8R 

Partition8 Ready 

 
Partition Keypad 

HIKVISION

System Fault

 

 

Keypad Standby Status Display Demonstration 

The standby status display demonstration is shown below. 

HIKVISION

 

SYS1D    SYS2R    SYS3A    SYS4R

SYS5R    SYS6R    SYS7R    SYS8R

 

V1.2.1  build  131211
2014.04.18  19:24:26

 

Summary of Contents for DS-PK00 series
































































Reviews:

No comments