HIKVISION DS-K1A801EF User Manual Download Page 90

Page: 90 / 126

Fingerprint Time Attendance Terminal

Access Control Type

Purpose:

The added cards can be assigned with different card type for the corresponding
usage.

Steps:

Click

Access Control Type

tab and select a card type.

Normal Card

: By default, the card is set as normal card.

Card for Disabled Person

: The door will remain open for the configured time

period for the cardholder.

Card in Blacklist

: The card swiping action will be uploaded and the door cannot

be opened.

Patrol Card

: The card swiping action can used for checking the working status of

the inspection staff. The access permission of the inspection staff is configurable.

Duress Card

: The card swiping action will be uploaded.

Super Card

: The card is valid for all the doors of the controller during the

configured schedule.

Visitor Card

: The card is assigned for visitors.

Click

Add

and select the available card.

Click

to confirm assigning the card(s) to the selected card type.

Click the

Apply

button to take effect of the new settings.

Notes:



You can click

Delete

to remove the card from the card type and the card

can be available for being re-assigned.



The attendance device only supports the normal card.

Card Reader Authentication

Purpose:

Summary of Contents for DS-K1A801EF































































































































Search results

Summary of Contents for DS-K1A801EF

Reviews:

Related manuals for DS-K1A801EF

Brands by name

Popular brands

HIKVISION DS-K1A801EF, User Manual

Search results

Summary of Contents for DS-K1A801EF

Reviews:

Related manuals for DS-K1A801EF

Brands by name

Popular brands