HIKVISION DS-K1A801EF User Manual Download Page 113

Page: 113 / 126

Fingerprint Time Attendance Terminal

106

Configuration Logs Searching

Purpose:

The Configuration Log files of the Access Control System can be searched by
time ,including One-card Configuration, Access Control Configuration, Downloading
Permission and System Configuration.

Steps:

Open the Log Search page.

Select the radio button of Configuration Logs.

Select the Operation Type of log files.

Click the icon to specify the start time and end time.

Click

Search

. The matched log files will display on the list.

You can check the operation time, log type and other information of the logs.

Note:

Please narrow the search condition if there are too many log files.

Control Logs Searching

Purpose:

The Control Log files of the Access Control System can be searched by time ,including
Access Control and Log Search.

Steps:

Open the Log Search page.

Select the radio button of Control Logs.

Select the Operation Type of log files.

Click the icon to specify the start time and end time.

Click

Search

. The matched log files will display on the list.

You can check the operation time, log type and other information of the logs.

Note:

Please narrow the search condition if there are too many log files.

Searching Configuration Log

Searching One-card Configuration Logs

Purpose:

Summary of Contents for DS-K1A801EF































































































































Search results

Summary of Contents for DS-K1A801EF

Reviews:

Related manuals for DS-K1A801EF

Brands by name

Popular brands

HIKVISION DS-K1A801EF, User Manual

Search results

Summary of Contents for DS-K1A801EF

Reviews:

Related manuals for DS-K1A801EF

Brands by name

Popular brands