manualshive.com logo in svg

Hewlett Packard Enterprise ProLiant DL20 Gen10, Maintenance And Service Manual

Share
Download
Hewlett Packard Enterprise ProLiant DL20 Gen10 Maintenance And Service Manual Download Page 85

CAUTION: To prevent damage to electrical components, take the appropriate anti-static precautions before
beginning any installation, removal, or replacement procedure. Improper grounding can cause electrostatic
discharge.

Prerequisites

Before you perform this procedure, make sure that you have a T-15 Torx screwdriver available.

Procedure

1.

If installed, 

remove the front bezel.

2.

Power down the server.

3.

Remove all power:

a. Disconnect each power cord from the power source.

b. Disconnect each power cord from the server.

4.

Disconnect all peripheral cables from the server.

5.

Remove the server from the rack.

6.

Remove the access panel.

7.

If installed, remove the processor air baffle.

8.

Remove the M.2 air guider.

9.

Allow the heatsink to cool.

10. Remove the heatsink:

a. Loosen one pair of diagonally opposite screws halfway, then loosen the other pair of screws.

b. Completely loosen all screws in the same sequence.

c. Remove the heatsink from the processor backplate.

Removal and replacement procedures

85

Summary of Contents for ProLiant DL20 Gen10


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands