manualshive.com logo in svg

Hewlett Packard Enterprise ProLiant DL20 Gen10, Maintenance And Service Manual

Share
Download
Hewlett Packard Enterprise ProLiant DL20 Gen10 Maintenance And Service Manual Download Page 82

a. Disconnect the chassis intrusion detection switch cable from the system board.

b. Open the latches that secure the switch to the DIMM guard.

c. Remove the chassis intrusion detection switch.

To replace the component, reverse the removal procedure.

Removing and replacing a fan

Procedure

1. If installed, remove the front bezel.

2. Power down the server.

3. Remove all power:

a. Disconnect each power cord from the power source.

b. Disconnect each power cord from the server.

4. Disconnect all peripheral cables from the server.

5. Remove the server from the rack.

6. Remove the access panel.

7. If installed, remove the processor air baffle before removing fan 1 or 2.

Removal and replacement procedures

82

Summary of Contents for ProLiant DL20 Gen10


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands