Hewlett Packard Enterprise ProLiant DL20 Gen10 Maintenance And Service Manual Download Page 144

Page: 144 / 153

Mechanical specifications

Specification

Value

Height

4.32 cm (1.70 in)

Depth

38.22 cm (15.05 in)

Width

43.46 cm (17.11 in)

Weight, maximum

9.46 kg (20.85 lb)

Weight, minimum

6.0 kg (13.22 lb)

Power supply specifications

Depending on the installed options and the regional location where the server was purchased, the server can be
configured with one of the following power supplies:

•

ATX 290W Non-hot-plug Power Supply (92% efficiency)

•

ATX 290W Platinum Non-hot-plug Power Supply (94% efficiency)

•

HPE 500W Flex Slot Platinum Hot-plug Low Halogen Power Supply

•

HPE 800W Flex Slot -48VDC Hot plug Low Halogen Power Supply

These are entry class power supply products for ProLiant Servers. For detailed power supply specifications, see the
QuickSpecs on the

Hewlett Packard Enterprise website.

ATX 290W Non-hot-plug Power Supply (92% efficiency)

Specification

Value

Input requirements

—

Rated input voltage

100 VAC to 240 VAC

Rated input frequency

50 Hz to 60 Hz

Rated input current

5.5 A

Maximum rated input power

331 W at 115 VAC

330 W at 230 VAC

Efficiency

No less than 88% at 100% load

No less than 92% at 50% load

No less than 88% at 20% load

Power supply output

—

Table Continued

Specifications

144

Summary of Contents for ProLiant DL20 Gen10


























































































































































Search results

Summary of Contents for ProLiant DL20 Gen10

Reviews:

Brands by name

Popular brands

Hewlett Packard Enterprise ProLiant DL20 Gen10, Maintenance And Service Manual

Search results

Summary of Contents for ProLiant DL20 Gen10

Reviews:

Brands by name

Popular brands