manualshive.com logo in svg

Hewlett Packard Enterprise ProLiant DL20 Gen10, Maintenance And Service Manual

Share
Download
Hewlett Packard Enterprise ProLiant DL20 Gen10 Maintenance And Service Manual Download Page 107

12. Connect all peripheral cables to the server.

13. Connect the power cords:

a. Connect each power cord to the server.

b. Connect each power cord to the power source.

14. Power up the server.

15. If removed, install the front bezel.

16. Properly dispose of the old battery.

For more information about proper battery disposal, contact an authorized reseller or an authorized service provider.

HPE Trusted Platform Module 2.0 Gen10 Option

The HPE Trusted Platform Module 2.0 Gen10 Option is not a customer-removable part.

CAUTION: If the TPM is removed from the original server and powered up on a different server, data stored in the
TPM including keys will be erased.

If you suspect a TPM board failure, leave the TPM installed and remove the system board. Contact a Hewlett Packard
Enterprise authorized service provider for a replacement system board and TPM board.

Removal and replacement procedures

107

Summary of Contents for ProLiant DL20 Gen10


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands