background image

2. Operation 
 

 
Have you read and understood the operating instructions, in particular section 

 

1 on safety and protection devices? 

 You 

may 

not

 use the device until you have done so! 

 
 

 
2.1. Handling non-rechargeable/rechargeable 
 batteries 

 
 

 
Depending on the version, HETRONIC radio remote control systems either 
come with a battery compartment for two or three 1.5 V alkaline mignon 
batteries 

 
 

or 

 

with a HETRONIC rechargeable battery/battery charger set (12/24 VDC or 
115/230 VAC depending on the transmitter type) and two HETRONIC 
interchangeable batteries 
 

or 

 
with a VersaPak rechargeable battery/battery charger set (115 V AC or 230 V AC) 
with two interchangeable VersaPak penlite batteries rated at 3.6 V each. 

 
 

  

 

  

 

 

If your HETRONIC radio remote control system was 
delivered with a battery compartment for alkaline mignon 
batteries, never attempt to charge the battery 
compartment with the alkaline batteries in a battery 
charger! 
Alkaline batteries are not capable of recharging; only 
batteries specially designed for this purpose can be 
recharged!  

 
 

 
 

 
 

Summary of Contents for CS 434

































Reviews: