HETRONIC CS 434 Operating Instructions & Installation Instructions Download Page 27

 

 

 

 

4. Maintenance

 

 
 
 
The employer is responsible for ensuring that devices for the wireless transmission of 
control commands are inspected by a qualified expert on a regular basis, and at the latest 
once annually. 
 
 
 
 
 
 

A qualified expert is someone who has adequate skills and knowledge 
in the field of wireless transmission of commands, based on relevant 
technical training and experience, and is familiar with applicable 
national industrial safety regulations, safety standards, guidelines and 
generally approved technical practice (including DIN standards, VDE 
standards, and technical standards of other member states of the 
European Union or other states party to the convention on the 
European Economic Area), to the extent that they can assess the 
operating safety of devices for the wireless transmission of control 
commands. 

 
 
 
 
 

 

 

 

 

5. Disposal

 

 
 
 
 
 
 

 

 

Do not pollute the environment! 

 

 

 

Electronic devices and their components are    

   hazardous 

waste! 

 

This applies particularly to rechargeable battery 

 packs! 

 

 

 

Use a specialist disposal company for recycling and  

   disposal! 
 

 

 

Defective rechargeable battery packs also can be  

   disposed 

of 

directly 

through 

HETRONIC! 

 

 

 

 

 
 
 
 

Summary of Contents for CS 434

































Reviews: