Hesai PandarXT-16 User Manual Download

Page: 50 / 83

4.2.1

Network Settings

Parameter

Options

Description

VLAN

Default: OFF

VLAN ID: 1 ~ 4094

To enable VLAN tagging:

Make sure the receiving host also supports VLAN.

Check the checkbox and input the lidar's VLAN ID (same as the receiving host's
VLAN ID).

Notes

Once configured, the VLAN ID does not change during firmware upgrades.

When VLAN is enabled, PTP connection will be lost; when VLAN is disabled, PTP
connection will automatically recover.

Warnings

If the lidar's VLAN ID differs from the receiving host's, users will lose access to web
control. To minimize such risks, the VLAN ID is zero (invalid value) by default.

When checking the checkbox, users will be alerted to input a valid VLAN ID.

When unchecking the checkbox, the VLAN ID will default to zero.

Destination IP

Any address except for
0.0.0.0, 127.0.0.1, and the
lidar's IP.

Default: 255.255.255.255

Mode

Destination IP

Broadcast (default)

255.255.255.255

Multicast

User-defined

Unicast

Same as the PC's IP address

Summary of Contents for PandarXT-16




















































































Search results

Summary of Contents for PandarXT-16

Reviews:

Related manuals for PandarXT-16

Brands by name

Popular brands

Hesai PandarXT-16, User Manual

Search results

Summary of Contents for PandarXT-16

Reviews:

Related manuals for PandarXT-16

Brands by name

Popular brands