HELVAR Minisensor User Manual Download Page 3

Page: 3 / 16

Data subject to change without notice. For more information visit our website: www.helvar.com

The Helvar Minisensor is a two channel luminaire-

mounted component containing three integrated sensors:

- Presence detector (PIR)

- Constant light sensor

- Infrared (IR) receiver.

The two separate channels (A & B) enable scene setting

& lighting control. The constant light sensor only adjusts

the output from channel A, where-as presence detection

& infrared control affect both channels.

The Minisensor is only compatible with the Helvar EL-si electronic DALI ballast range. Sensor set-up &

programming is achieved using the Helvar Digidim infrared remote control.

Dimensions

Installation

3.3mm

25mm

32mm

max.

1.2mm

4mm

Clip on assembly

Surface mounting

Dimension

(mm)

26.4

15.5

27.5

39.8

21.6

Weight

25g

750

200

L1 + L2

950

Introduction

Summary of Contents for Minisensor

















Search results

Summary of Contents for Minisensor

Reviews:

Related manuals for Minisensor

Brands by name

Popular brands

HELVAR Minisensor, User Manual

Search results

Summary of Contents for Minisensor

Reviews:

Related manuals for Minisensor

Brands by name

Popular brands