HELVAR Minisensor User Manual Download Page 13

Page: 13 / 16

Data subject to change without notice. For more information visit our website: www.helvar.com

Technical specifications

Constant light sensor

Reception area:

100°

Measuring range:

50-1000 lux

IR-receiver

Frequency

36kHz

Presence detector

Detection area 4.5 x 3.0m (mounting height 3.0m)

Electric data

Internal communication with Helvar EL-si electronic ballast.

Operation conditions

Ambient temperature range

0°C to 50°C

Storage temperature range

-10°C to 70°C

Relative humidity

90% maximum, non-condensing

Conformity & Standards

Safety:

Only valid if sensor is mounted in the same fitting as the ballasts.

Safety

EN61347-2-11, EN61347-1, EN60598-1

IP rating

Isolation

4kV

Finish:

White thermoplastic

Protection:

Single insulation

Wire length:

Max. from Minisensor to furthest ballast

15m

Note:

•

The Minisensor is not designed for installation outside of a luminaire.

Summary of Contents for Minisensor

















Search results

Summary of Contents for Minisensor

Reviews:

Related manuals for Minisensor

Brands by name

Popular brands

HELVAR Minisensor, User Manual

Search results

Summary of Contents for Minisensor

Reviews:

Related manuals for Minisensor

Brands by name

Popular brands