Heatrae Sadia Multipoint 10 and 15 litre Fitting Instructions Manual Download Page 4

4

2.3

 Specific safety instructions

WARNING

DO NOT operate the  product if:

 

`

Water ceases to flow during use.

 

`

Water has entered inside the 

product because of an incorrectly 

fitted cover.

 

`

If the appliance is damaged. 

(in all cases turn off mains power and 

isolate water supply)

 

`

If water discharges from the 

temperature/pressure relief valve 

on the product shut down. Do not 

turn off any water supply. Contact 

a competent installer for unvented 

water heaters to check the system.

 

`

Do not tamper with any of the 

safety valves fitted to the system. 

If a fault is suspected contact a 

competent installer.

 

`

DO NOT bypass the thermal cut-

out in any circumstance.

2.  Safety

2.1 General safety warnings

DANGER

This product is unvented and as such 

becomes pressurised when in operation. 

The combination of pressurisation and hot 

water could lead to serious physical injury 

if the safety instructions in this manual are 

not adhered to.

DANGER

Do not install where the unit may freeze.

WARNING

 

`

Only competent persons having 

received adequate training are 

permitted to work on the product 

and the installation.

 

`

Do not tamper with the safety 

valve supplied.

 

`

Before any work, switch off the 

mains supply to the appliance.

 

`

Do not switch on if there is a 

possibility that the water in the 

appliance is frozen.

CAUTION

Do not operate immersion heater until the 

product has been filled with water.

2.2 Recommendations

CAUTION

 

`

Annual maintenance is 

recommended by a competent 

person.

Summary of Contents for Multipoint 10 and 15 litre

















Reviews: